Jet Tools Drill JDP 15M MF User Manual

This .pdf document is bookmarked  
Operating Instructions and Parts Manual  
Drill Press  
Models JDP-15M/MF  
WALTER MEIER (Manufacturing) Inc.  
427 New Sanford Road  
LaVergne, Tennessee 37086  
Ph.: 800-274-6848  
Part No. M-354165  
Revision A1 04/2010  
Copyright © 2010 Walter Meier (Manufacturing) Inc.  
 
Table of Contents  
Table of Contents ...............................................................................................................................3  
Warnings............................................................................................................................................4  
Specifications .....................................................................................................................................6  
Shipping Contents ..............................................................................................................................7  
Required Tools...................................................................................................................................7  
Assembly ...........................................................................................................................................8  
Before Assembly .............................................................................................................................8  
Column Assembly ...........................................................................................................................8  
Table Bracket..................................................................................................................................8  
Crank Handle and Table Lock Handle...............................................................................................8  
Column Lock Handle .......................................................................................................................9  
Table Installation.............................................................................................................................9  
Head Assembly...............................................................................................................................9  
Chuck and Arbor Installation ............................................................................................................9  
Chuck and Arbor Removal .............................................................................................................10  
Adjustment .......................................................................................................................................10  
Depth Stop Adjustment ..................................................................................................................10  
Changing Spindle Speeds..............................................................................................................10  
Return Spring Adjustment ..............................................................................................................11  
Work Light ....................................................................................................................................12  
Table Tilt Adjustment .....................................................................................................................12  
Operation.........................................................................................................................................12  
Installing Drills...............................................................................................................................12  
Positioning the Workpiece..............................................................................................................12  
Using the Vise...............................................................................................................................12  
Basic Operation.............................................................................................................................12  
Maintenance ....................................................................................................................................13  
Lubrication .......................................................................................................................................13  
Electrical ..........................................................................................................................................13  
115 Volt Operation ........................................................................................................................13  
230 Volt Operation ........................................................................................................................13  
Grounding Instructions...................................................................................................................14  
Extension Cords............................................................................................................................14  
Troubleshooting................................................................................................................................15  
Replacement Parts ...........................................................................................................................16  
Exploded View Drawing JDP-15M/MF ............................................................................................17  
Parts List JDP-15M/MF..................................................................................................................18  
Parts List JDP-15M/MF..................................................................................................................19  
Parts List JDP-15M/MF..................................................................................................................20  
Wiring Diagram.................................................................................................................................21  
JDP – 15M/MF – 115V...................................................................................................................21  
JDP – 15M/MF – 230V...................................................................................................................21  
The specifications in this manual are given as general information and are not binding. Walter Meier  
(Manufacturing) Inc., reserves the right to effect, at any time and without prior notice, changes or  
alterations to parts, fittings, and accessory equipment deemed necessary for any reason whatsoever.  
3
 
Warnings  
1. Read and understand the entire owners manual before attempting assembly or operation.  
2. Read and understand the warnings posted on the machine and in this manual. Failure to comply with  
all of these warnings may cause serious injury.  
3. Replace the warning labels if they become obscured or removed.  
4. This drill press is designed and intended for use by properly trained and experienced personnel only.  
If you are not familiar with the proper and safe operation of a drill press, do not use until proper  
training and knowledge have been obtained.  
5. Do not use this drill press for other than its intended use. If used for other purposes, Walter Meier  
(Manufacturing) Inc., disclaims any real or implied warranty and holds itself harmless from any injury  
that may result from that use.  
6. Always wear approved safety glasses/face shields while using this drill press. Everyday eyeglasses  
only have impact resistant lenses; they are not safety glasses.  
7. Before operating this drill press, remove tie, rings, watches and other jewelry, and roll sleeves up past  
the elbows. Remove all loose clothing and confine long hair. Non-slip footwear or anti-skid floor strips  
are recommended. Do not wear gloves.  
8. Wear ear protectors (plugs or muffs) during extended periods of operation.  
9. Some dust created by power sanding, sawing, grinding, drilling and other construction activities  
contain chemicals known to cause cancer, birth defects or other reproductive harm. Some examples  
of these chemicals are:  
Lead from lead based paint.  
Crystalline silica from bricks, cement and other masonry products.  
Arsenic and chromium from chemically treated lumber.  
Your risk of exposure varies, depending on how often you do this type of work. To reduce your  
exposure to these chemicals, work in a well-ventilated area and work with approved safety  
equipment, such as face or dust masks that are specifically designed to filter out microscopic  
particles.  
10. Do not operate this machine while tired or under the influence of drugs, alcohol or any medication.  
11. Make certain the switch is in the OFF position before connecting the machine to the power supply.  
12. Make certain the machine is properly grounded.  
13. Make all machine adjustments or maintenance with the machine unplugged from the power source.  
14. Remove adjusting keys and wrenches. Form a habit of checking to see that keys and adjusting  
wrenches are removed from the machine before turning it on.  
15. Keep safety guards in place at all times when the machine is in use. If removed for maintenance  
purposes, use extreme caution and replace the guards immediately.  
16. Make sure the drill press is firmly secured to the floor or bench before use.  
17. Check damaged parts. Before further use of the machine, a guard or other part that is damaged  
should be carefully checked to determine that it will operate properly and perform its intended  
function. Check for alignment of moving parts, binding of moving parts, breakage of parts, mounting  
and any other conditions that may affect its operation. A guard or other part that is damaged should  
be properly repaired or replaced.  
18. Provide for adequate space surrounding work area and non-glare, overhead lighting.  
19. Keep the floor around the machine clean and free of scrap material, oil and grease.  
4
 
20. Keep visitors a safe distance from the work area. Keep children away.  
21. Make your workshop child proof with padlocks, master switches or by removing starter keys.  
22. Give your work undivided attention. Looking around, carrying on a conversation and “horse-play” are  
careless acts that can result in serious injury.  
23. Maintain a balanced stance at all times so that you do not fall or lean against the spindle or other  
moving parts. Do not overreach or use excessive force to perform any machine operation.  
24. Use the right tool at the correct speed and feed rate. Do not force a tool or attachment to do a job for  
which it was not designed. The right tool will do the job better and safer.  
25. Use recommended accessories; improper accessories may be hazardous.  
26. Maintain tools with care. Keep drill bits sharp and clean for the best and safest performance. Follow  
instructions for lubricating and changing accessories.  
27. Make sure the work piece is securely attached or clamped to the table. Never use your hand to hold  
the work piece.  
28. Turn off the machine before cleaning. Use a brush or compressed air to remove chips or debris — do  
not use your hands.  
29. Do not stand on the machine. Serious injury could occur if the machine tips over.  
30. Never leave the machine running unattended. Turn the power off and do not leave the machine until it  
comes to a complete stop.  
31. Remove loose items and unnecessary work pieces from the area before starting the machine.  
Familiarize yourself with the following safety notices used in this manual:  
This means that if precautions are not heeded, it may result in minor injury and/or  
possible machine damage.  
This means that if precautions are not heeded, it may result in serious injury or possibly  
even death.  
- - SAVE THESE INSTRUCTIONS - -  
5
 
Specifications  
Model Number............................................................JDP-15M........................................... JDP-15MF  
Stock Number .............................................................. 354165................................................ 354166  
Swing..................................................................................15”.......................................................15"  
Type .............................................................................. Bench....................................................Floor  
Drilling Capacity..................................................................5/8”......................................................5/8”  
Chuck Size.........................................................................5/8”......................................................5/8”  
Spindle Travel .................................................................3-1/8”...................................................3-1/8”  
Spindle Distance to Base ............................................... 16-1/2”.......................................................48"  
Spindle Distance to Table (max.) ..........................................24”.......................................................29"  
Table Size (Length x Width) ...................................16-1/2" x 13".........................................16-1/2" x 13"  
Spindle Taper........................................................... MT-2/JT-3............................................ MT-2/JT-3  
Column Diameter.............................................................2-7/8”...................................................2-7/8”  
Number of Spindle Speeds....................................................16........................................................16  
Range of Spindle Speeds (RPM) ..............................200 - 3,630...........................................200 - 3,630  
Base Size........................................................10-7/8” x 18-1/2”.........................................11” x 19-3/4”  
Overall Dimensions (H x W x D)..................... 39-1/2" x 13" x 31"......................................63" x 13" x 31"  
Motor.................................. TEFC 3/4HP, 115/230V, 60Hz, 1Ph....... TEFC 3/4HP, 115/230V, 60Hz, 1Ph  
Net Weight, approximate ..............................................156 lbs.................................................161 lbs.  
Gross Weight, approximate ...........................................163 lbs.................................................167 lbs.  
Carton Size (L x W x H/in): ..................................... 32 x 22 x 12......................................... 56 x 20 x 11  
The above specifications were current at the time this manual was published, but because of our policy of  
continuous improvement, Walter Meier (Manufacturing) Inc., reserves the right to change specifications at  
any time and without prior notice, without incurring obligations.  
6
 
Shipping Contents  
Unpack the carton and verify that all parts listed  
below are included.  
Other Material  
Main Parts  
1 ea  
1 ea  
Owner’s Manual  
Warranty Registration Card  
1 ea  
1 ea  
Head Assembly  
Table  
1 set Column and Table Bracket Assembly  
1 ea Base  
Required Tools  
1. 17mm Box Wrench or a 6” – 8” Adjustable  
Wrench  
Additional Parts  
1. 1 set Chuck and Chuck Key  
2. 15/16" wrench  
2. 1 pc  
3. 1 pc  
4. 1 pc  
5. 1 pc  
6. 1 pc  
Arbor  
Drift Key  
Table Crank Handle  
Table Lock Handle  
Column Lock Handle  
7. 3 pcs Downfeed Handles and Knobs  
8. 4 pcs M10 x 40 Hex Cap Screws  
9. 1 set Hex Wrenches (3mm, 5mm, 6mm)  
Additional Parts  
7
 
Referring to Figures 2 and 3:  
Assembly  
4. Remove the wrap and take the rack ring (D)  
and rack (B) off the column (C).  
5. Install the table bracket (A) together with the  
rack (B) as shown in Figure 2.  
Read  
and  
understand  
all  
assembly  
instructions before attempting assembly!  
Failure to comply may cause serious injury!  
Before Assembly  
1. Remove the contents from the shipping  
container.  
2. Compare the contents of the shipping  
container with the list found above. Report  
any shortages or damage to your JET  
distributor.  
3. Clean all rust protected surfaces with  
kerosene or a light solvent. Do not use  
lacquer thinner, paint thinner, or gasoline.  
These will damage plastic components and  
painted surfaces.  
Figure 2  
6. Slide the rack ring (D) over the column (C),  
placing it so it rests against the rack (B) as  
shown in Figure 3 and tighten firmly.  
Column Assembly  
Referring to Figure 1:  
1. Place the base (A) on a level floor.  
2. Place the column assembly (B) on the base  
(A) and align the holes in the column  
support with the holes in the base.  
Note: The column shown in Figure 1 is for  
the JDP-15MF. While the JDP-15M column  
is slightly different in appearance, the  
assembly procedure is the same.  
3. Using a 17mm wrench, secure the column  
(B) with four M10 x 40 hex cap screws (C) to  
the base.  
Figure 3  
Crank Handle and Table Lock Handle  
Referring to Figure  
assembled):  
4
(shown already  
1. Loosen the setscrew (B) on the table crank  
handle (A).  
2. Slide the handle (A) onto the table bracket  
shaft.  
3. Turn the handle until the setscrew is  
opposite the flat section on the shaft, and  
tighten the setscrew to secure the handle.  
Figure 1  
Table Bracket  
4. Install the table lock handle (C), but do not  
When shipped, the rack ring and rack are  
bundled together with the column in plastic  
wrap.  
tighten.  
8
 
Head Assembly  
Referring to Figure 7:  
1. With the aid of a second person, carefully lift  
the head onto the column top and slide it  
down into position  
Figure 4  
The head assembly is heavy! Use care when  
lifting onto the column!  
Column Lock Handle  
2. Rotate head assembly until sides of the  
pulley cover are parallel with the sides of the  
base.  
Referring to Figure 5:  
Thread the column lock handle (D) into the table  
bracket (E).  
3. Tighten two setscrews (A) with a 5mm hex  
wrench (provided) until they are snug.  
Figure 7  
4. Install three downfeed handles (B) into the  
Figure 5  
downfeed hub (C).  
Table Installation  
Chuck and Arbor Installation  
Referring to Figure 6:  
Referring to Figure 8:  
1. Place the table (A) on the bracket (B).  
2. Tighten the table lock handle (C).  
1. Twist the chuck (B) to retract the chuck jaws  
if they are exposed.  
2. Install the chuck (B) to the arbor (A) tightly.  
3. Insert the chuck and arbor assembly into the  
spindle (C). Pull the downfeed handle down  
to press the arbor in place.  
Note: Put a piece of scrap wood (D) on the table  
to protect the chuck nose when pulling the  
downfeed handle (E) down to press into place.  
Figure 6  
9
 
1. Use a pencil to mark the depth the bit will  
drill into the workpiece.  
2. With the drill bit in the chuck, lower  
downfeed handle to advance bit to your  
mark (A).  
3. With your other hand, advance the lock nuts  
(B) on the depth stop rod until they are snug  
to the seat (C).  
4. The drill bit will now advance to this point.  
5. To release, advance the nuts counter-  
clockwise to the top of the depth stop.  
Figure 8  
Chuck and Arbor Removal  
Referring to Figure 9:  
1. Unplug machine from the power source.  
2. Raise the table until it is about seven inches  
below the chuck.  
3. Place a piece of scrap wood on the table,  
and lower quill (A) using the downfeed  
handle.  
4. Rotate spindle to align the keyhole in the  
spindle with the keyhole in the quill.  
5. Insert the drift key (B) into the aligned slots  
and tap lightly. The chuck and arbor  
assembly should fall from the spindle.  
Figure 10  
Changing Spindle Speeds  
A spindle speed and pulley/belt arrangement  
chart is found on the inside of the pulley cover  
(D, Fig. 11). The chart is also shown in Figure  
12. Refer to this chart whenever changing  
speeds.  
To change spindle speeds:  
1. Unplug the machine from the power source.  
2. Loosen two bar knobs (E, Fig. 11) found on  
each side of the head assembly.  
3. Rotate the tension adjuster clockwise (F,  
Fig. 11) to bring the motor base as close to  
the head as possible.  
Figure 9  
Adjustment  
4. For desired speed, change the location of  
belts per pulley/belt arrangement chart.  
Depth Stop Adjustment  
Referring to Figure 10:  
5. Rotate  
the  
tension  
adjuster  
counterclockwise (F. Fig. 11) to tension the  
belts.  
To drill multiple holes at the same preset depth,  
use the depth stop:  
10  
 
6. Tighten two bar knobs (E, Fig. 11). Belts  
are properly tensioned when finger and  
thumb pressure midway between the two  
pulleys causes approximately ½” deflection.  
Figure 11  
Figure 12  
Return Spring Adjustment  
The return spring is adjusted at the factory and  
should not need further adjustment. If  
adjustment is deemed necessary, follow the  
steps below while referring to Figure 13:  
1. Unplug the machine from the power source.  
2. Loosen two hex nuts (A). Do not remove.  
3. Firmly hold the coil spring cover (B).  
4. Pull out the cover and rotate until the pin (C)  
on the return spring plate engages the next  
notch in the coil spring cover. Turn the  
cover clockwise to decrease tension and  
counter-clockwise to increase tension.  
5. Tighten two hex nuts (A). Do not over-  
tighten. Nuts should not contact the housing  
when tight.  
The hex nuts should be  
tightened against each other.  
Figure 13  
11  
 
Work Light  
Install a light bulb, no larger than 60 watts into  
the socket accessed from beneath the head.  
The rocker switch controls the light switch (D,  
Fig. 13). IMPORTANT: If the drill press is  
connected to 230 volt power, you must install a  
bulb rated for 230 volt.  
Table Tilt Adjustment  
The table tilt adjustments are made on the table  
bracket under the table.  
To tilt the table (refer to Figures 14 and 15):  
Figure 15  
Operation  
In the following steps do not over loosen.  
This could result in the table assembly to  
separate from the column, fall and cause  
injury.  
Installing Drills  
Insert the drill into the chuck jaws about  
1" (25.4mm) long. When using a small drill do  
not insert it so far that the jaws touch the flutes  
of the drill. Make sure that the drill is centered in  
the chuck before tightening the chuck with the  
key.  
1. Loosen the socket head set screw (A) with a  
3mm hex wrench.  
2. Using a 15/16" wrench, loosen the hex cap  
screw (B), and tilt the table to the desired  
angle by aligning the arrow (C, Fig. 15) on  
the rotating part of the bracket to the desired  
angle (in degrees) displayed on the scale  
(D, Fig 15) at the base of the bracket.  
Positioning the Workpiece  
Always place a piece of wood (or plywood) on  
the table. This will prevent "splintering" or  
making heavy burrs on the underside of the  
workpiece as the drill breaks through. The wood  
should contact the left side of the column.  
3. Tighten the hex cap screw (B).  
4. Tighten the socket head set screw (A).  
Using the Vise  
For the small workpiece that cannot be clamped  
to the table, use a drill press vise. The vise must  
be clamped or bolted to the table. Always use a  
back-up piece of scrap wood to cover the table.  
This protects both the table and the drill bit.  
Basic Operation  
Place material to be drilled in such as way as to  
come into contact with the left side of the  
column. This prevents the material from  
spinning.  
If the work piece is not large enough to come  
into contact with the column, use a clamp or  
drill press vise that is securely fastened to  
the table! Failure to comply may cause  
serious injury!  
Feed the bit into the material with only enough  
force to allow the drill bit to work. Feeding too  
slowly may cause burning of the workpiece.  
Feeding too quickly may cause the motor to stop  
and/or the drill bit to break.  
Figure 14  
12  
 
Generally speaking, the smaller the drill bit, the  
greater the RPM required. Wood requires higher  
speeds than metal. Metal is usually drilled at  
slower speeds.  
In dusty environments, frequently blow out any  
dust that accumulates inside the motor.  
Figure 16  
Maintenance  
230 Volt Operation  
Referring to Figure 17:  
If 230V, single-phase operation is desired, the  
following instructions must be followed:  
Before any intervention on the machine,  
disconnect it from the electrical supply by  
pulling out the plug or switching off the main  
switch! Failure to comply may cause serious  
injury.  
1. Disconnect the machine from the power  
source.  
2. The JET drill press motor has four  
numbered leads that are factory connected  
for 115V operation, as shown in (A). For  
230V operation reconnect the leads as  
shown in (B).  
A coat of automobile-type wax applied to the  
table and column will help to keep the surfaces  
clean.  
If the power cord is worn, cut, or damaged in  
any way, have it replaced immediately.  
3. The 115V attachment plug (C), supplied with  
the drill press, must be replaced with a  
UL/CSA listed plug suitable for 230V  
operation (D). Contact your local Authorized  
JET Service Center or qualified electrician  
for proper procedures to install the plug.  
The drill press must comply with all local and  
national codes after the 230-volt plug is  
installed.  
Lubrication  
All of the ball bearings are packed with grease at  
the factory. They require no further lubrication.  
Periodically lubricate the gear, rack, table  
elevation mechanism, the splines (grooves) in  
the spindle, and the teeth of the quill with a #2  
tube grease.  
4. The drill press with a 230-volt plug should  
only be connected to an outlet having the  
same configuration as shown in (D). No  
adapter is available nor should be used with  
the 230-volt plug.  
Electrical  
115 Volt Operation  
Referring to Figure 16:  
5. The bulb installed in the work light must be  
rated for 230 volt power.  
As received from the factory, your drill press is  
ready to run at 115-volt operation. This drill  
press, when wired for 115 volt, is intended for  
use on a circuit that has an outlet and a plug that  
looks like the one illustrated in (A). A temporary  
adapter, which looks like the adapter shown in  
(B), may be used to connect this plug to a two-  
pole receptacle if a properly grounded outlet is  
not available. The temporary adapter should  
only be used until a properly grounded outlet  
can be installed by a qualified electrician. This  
adapter is not applicable in Canada. The green  
colored rigid ear, lug, or tab, extending from the  
adapter, must be connected to a permanent  
ground such as a properly grounded outlet box.  
Figure 17  
13  
 
Grounding Instructions  
Extension Cords  
Make sure your extension cord is in good  
condition. When using an extension cord, be  
sure to use one heavy enough to carry the  
current your machine will draw. An undersized  
cord will cause a drop in the line voltage  
resulting in power loss and overheating. The  
following table shows the correct size to use  
depending on the cord length and nameplate  
ampere rating. If in doubt, use the next heavier  
gauge. Remember, the smaller the gauge  
number, the heavier the cord.  
This tool must be grounded while in use to  
protect the operator from electric shock.  
In the event of a malfunction or breakdown,  
grounding provides a path of least resistance for  
electric current to reduce the risk of electric  
shock. This tool is equipped with an electric cord  
having an equipment-grounding conductor and a  
grounding plug. The plug must be plugged into a  
matching outlet that is properly installed and  
grounded in accordance with all local codes and  
ordinances.  
Length of  
AWG  
Do not modify the plug provided. If it will not fit  
the outlet, have the proper outlet installed by a  
qualified electrician.  
Cord  
0–25  
16  
14  
Improper connection of the equipment-  
grounding conductor can result in a risk of  
electric shock. The conductor, with insulation  
having an outer surface that is green with or  
without yellow stripes, is the equipment-  
grounding conductor. If repair or replacement of  
the electric cord or plug is necessary, do not  
connect the equipment-grounding conductor to a  
live terminal.  
25-50  
The drill press with a 230-volt plug should only  
be connected to an outlet having the same  
configuration (D, Fig. 17). No adapter is  
available or should be used with the 230-volt  
plug.  
Check with a qualified electrician or service  
personnel if the grounding instructions are not  
completely understood, or if in doubt as to  
whether the tool is properly grounded. Use only  
three wire extension cords that have three-prong  
grounding plugs and three-pole receptacles that  
accept the tool’s plug.  
Important: In all cases (115 or 230 volts), make  
certain the receptacle in question is properly  
grounded. If you are not sure, have a registered  
electrician check the receptacle.  
Repair or replace a damaged or worn cord  
immediately.  
14  
 
Troubleshooting  
Trouble  
Probable Cause  
Remedy  
Drill press unplugged from wall, or  
motor.  
Check all plug connections.  
Drill press will not  
start.  
Fuse blown, or circuit breaker tripped. Replace fuse, or reset circuit breaker.  
Cord damaged.  
Replace cord.  
Starting capacitor bad.  
Replace starting capacitor.  
Replace with adequate size and  
length cord.  
Extension cord too light or too long.  
Low current.  
Drill press does not  
come up to speed.  
Contact a qualified electrician.  
Adjust stand so that it rests evenly on  
the floor.  
Stand on uneven surface.  
Bad belt(s).  
Drill Press vibrates  
excessively.  
Replace belts.  
Adjust belt tension. See the  
Changing Spindle Speeds section.  
Incorrect belt tension.  
Lubricate spindle. See the  
Lubrication section.  
Dry spindle.  
Noisy Operation.  
Check tightness of retaining nut on  
pulley, and tighten if necessary.  
Loose spindle pulley.  
Loose motor pulley.  
Incorrect Speed.  
Tighten setscrews in pulleys.  
Change to appropriate speed; see the  
Changing Spindle Speeds section.  
Retract drill bit frequently to remove  
chips.  
Chips not clearing from hole or bit.  
Workpiece Burns.  
Drill bit wanders.  
Dull drill bit.  
Resharpen, or replace drill bit.  
Increase feed rate.  
Feeding too slowly.  
Bit sharpened incorrectly.  
Bent drill bit.  
Resharpen bit correctly.  
Replace drill bit.  
Bit, or chuck not installed properly.  
Reinstall the chuck, or bit properly.  
Wood splinters on the  
underside.  
Place a scrap board underneath the  
workpiece to prevent splintering.  
No backing board used.  
Workpiece pinching the bit.  
Excessive feed rate.  
Support or clamp workpiece.  
Decrease feed rate.  
Drill bit binds in  
workpiece.  
Chuck jaws not tight.  
Tighten chuck jaws.  
Adjust belt tension. See the Changing  
Spindle Speeds section.  
Improper belt tension.  
15  
 
Troubleshooting (cont.)  
Trouble  
Probable Cause  
Remedy  
Bent drill bit.  
Replace drill bit.  
Excessive drill bit  
runout, or wobble.  
Worn spindle bearings.  
Bit, or chuck not properly installed.  
Replace spindle bearings.  
Reinstall the bit, or chuck properly.  
Adjust spring tension. See the Return  
Spring Adjustment section.  
Quill returns too slow,  
or too fast.  
Spring has improper tension.  
Chuck or arbor does  
not stay in place.  
Dirt, grease, etc on arbor, chuck, or  
spindle.  
Clean all mating surfaces thoroughly  
with a cleaner degreaser.  
Replacement Parts  
Replacement parts are listed on the following pages. To order parts or reach our service department, call  
1-800-274-6848, Monday through Friday (see our website for business hours, www.waltermeier.com).  
Having the Model Number and Serial Number of your machine available when you call will allow us to  
serve you quickly and accurately.  
16  
 
Exploded View Drawing JDP-15M/MF  
17  
 
Parts List JDP-15M/MF  
Index No. Part No.  
Description  
Size  
Qty  
1A............ 10600110................Base for JDP-15M ..............................................................................1  
1B............ 10800101................Base for JDP-15MF ............................................................................1  
2A............ JDP15-1002A..........Column Holder for JDP-15M................................................................1  
2B............ 10600204................Column Holder for JDP-15MF..............................................................1  
3.............. TS-2279121 ............Hex Socket Set Screw ......................................M10-12 ......................3  
4A............ JDP15-1004A..........Body Column for JDP-15M..................................................................1  
4B............ JDP15-1004B..........Body Column for JDP-15MF................................................................1  
5.............. TS-2229403 ............Hex Head Bolt ..................................................M10x40......................4  
6.............. 10600604................Table Bracket .....................................................................................1  
................ JDP15-1006 ............Table Bracket Assy (includes #6 thru #18)............................................1  
7.............. 10600702................Gear ..................................................................................................1  
8.............. 10600802................Gear Shaft .........................................................................................1  
9.............. 10600902................Worm.................................................................................................1  
10A.......... 10601009A1............Crank Handle Assy .............................................................................1  
12............ JDP15-1012 ............Table Bracket .....................................................................................1  
13............ TS-0071011 ............Hex Head Bolt ..................................................5/8-11 x 1-1/2.............1  
14............ TS-2276101 ............Hex Socket Set Screw ......................................M6-10........................1  
16............ 10601601................Tilting Scale .......................................................................................1  
17............ JDP15-1017 ............Centering Scale..................................................................................1  
18............ JDP15-1018 ............Drive Screw......................................................Φ 2.3-5 ......................2  
19............ 10601901................Column Lock Handle.........................................M12*1.75-35 ..............1  
20............ 10602001................Table Lock Handle............................................M10*1.5 ....................1  
21............ JDP15-1021 ............Table .................................................................................................1  
22A.......... 10602204................Rack for JDP-15M ..............................................................................1  
22B.......... 10602205................Rack for JDP-15MF ............................................................................1  
23............ 10602304................Rack Ring ........................................................Φ 73.5........................1  
24............ TS-2276081 ............Hex Socket Set Screw ......................................M6-8..........................1  
25............ JDP15-1025 ............Head..................................................................................................1  
26............ TS-2279121 ............Hex Socket Set Screw ......................................M10-12 ......................2  
27............ JDP15-1027 ............Lamp Socket ......................................................................................1  
28............ TS-1534042 ............Cr. Re. Pan Head Screw ...................................M6-12........................2  
29............ 10602901................Handle Shifter ....................................................................................1  
30............ 10603002................Motor Bar Shifter ................................................................................1  
31............ TS-2228161 ............Hex Head Bolt ..................................................M8-16........................1  
32............ 10603206................Motor Rod..........................................................................................1  
33............ 10603301................Shifter Bolt .......................................................M10-33 ......................2  
34............ 10603416................Motor Base.......................................................75*125.......................1  
35............ 2502NBC412...........Spring Washer..................................................Φ1/2".........................1  
36............ TS-1540081 ............Hex Nut............................................................M12...........................2  
37............ 10603704................Hub ...................................................................................................1  
38............ 10603807................Feed Shaft .........................................................................................1  
................ JDP15-1038 ............Feed Shaft Assy (includes #37 thru #39) ..............................................1  
39............ TS-209402 ..............Roll Pin............................................................M5-16........................1  
43A.......... JDP15-1043 ............Handle Bar .........................................................................................1  
45............ 10604505................Scale Ring .........................................................................................1  
50A.......... JDP15-1050 ............Spring Cap.........................................................................................1  
51............ 10605115................Shaft Seat..........................................................................................1  
53............ TS-0561052 ............Hex Nut............................................................1/2-20........................1  
54............ 10605403................Quill Set Screw.................................................M10-28 ......................1  
55............ TS-1540071 ............Hex Nut............................................................M10...........................1  
56............ 10605608................Quill.................................................................MT2...........................1  
................ JDP15-1056 ............Quill and Spindle Assy (includes #56 thru # 64) ....................................1  
57............ 10605702................Rubber Washer ..................................................................................1  
58............ 10605822................Spindle ............................................................MT2...........................1  
18  
 
Parts List JDP-15M/MF  
Index No. Part No.  
Description  
Size  
Qty  
59............ 2001ZZ6204............Ball Bearing........................................................................................1  
61............ 2001ZZ6203............Ball Bearing........................................................................................1  
62............ TS-2360161 ............Washer ............................................................M16...........................1  
63............ 10606301................Nut Lock ............................................................................................1  
64............ 10606401................Spindle Nut ........................................................................................1  
65............ 10606505................Driving Sleeve ....................................................................................1  
................ JDP15-1065 ............Driving Sleeve Assy (includes #65 thru #67) .........................................1  
66............ 2001ZZ6204............Ball Bearing........................................................................................2  
67............ 10606703................Rack ring..........................................................Φ 45 T=4....................1  
68............ 10606801................Retaining Ring....................................................................................2  
69............ 10606904................Pulley Set Nut ....................................................................................1  
70............ JDP15-1070 ............Spindle Pulley ....................................................................................1  
71............ 21015M2J30 ...........Drilling Arbor ....................................................MT2*JT3....................1  
72A.......... JDP15-1072 ............Chuck Assy........................................................................................1  
73............ 10607303................Wedge Shifter ....................................................................................1  
74............ JDP15-1074 ............Motor.................................................................................................1  
................ JDP15-1074A..........Centrifugal Switch (not shown) ............................................................1  
................ JDP15-1074B..........Capacitor (not shown) .........................................................................1  
75............ JDP15-1075 ............Motor Wire.........................................................................................1  
76............ TS-2208201 ............Hex. Hd. Screw ................................................M8-20........................4  
77............ TS-1550061 ............Flat Washer......................................................M8.............................8  
78............ TS-1540061 ............Hex Nut............................................................M8.............................4  
79............ JDP15-1079 ............Motor Pulley .......................................................................................1  
80............ 2571MNC307 ..........Parallel Key......................................................5*5-20........................1  
81............ TS-1504021 ............Hex Socket Set Screw ......................................M8-12........................1  
83............ JDP15-1083 ............Strain Relief .......................................................................................1  
84............ TS-1534042 ............Cr. Re. Pan Head Screw ...................................M6-12........................1  
85............ JDP15-1085 ............Power Cable ......................................................................................1  
87............ JDP15-1087 ............Rocker Switch ....................................................................................1  
88............ JDP15-1088 ............Switch Box.........................................................................................1  
89............ TS-1533042 ............Cr. Re. Pan Head Screw ...................................M5-12........................3  
90A.......... JDP15-1090 ............Pulley Cover Assy...............................................................................1  
................ JDP15-1090A..........U Shaped Protecting Rubber (not shown).............................................1  
92............ JDP15-1092 ............Cr. Re. Round Washer Hd. Screw......................M6*1.0-12..................4  
95............ JDP15-1095 ............Center Pulley......................................................................................1  
................ JDP15-1095A..........Center Pulley Assy (includes #95 thru #98) ..........................................1  
96............ JDP15-1096 ............Ball Bearing........................................................................................2  
98............ 10609801................Center Pulley Shaft.............................................................................1  
99............ VB-A28 ...................V-Belt...............................................................A-28...........................1  
101.......... TS-0680021 ............Flat Washer...................................................... 1/4............................4  
106.......... TS-0561052 ............Hex Nut…………………………………………….1/2-20 ..........................1  
109.......... JDP15-1109 ............Clamp-Cord........................................................................................3  
110.......... 2668BBDA23...........Cr. Re. Pan Head Screw ..................................M5-8..........................3  
112.......... 10611201................Chuck Key Holder...............................................................................1  
113.......... TS-2286122 ............Cr. Re. Round Washer Hd. Screw......................M6-12........................1  
119.......... VB-A26 ...................V-Belt...............................................................A-26...........................1  
128.......... TS-2285162 ............Cr. Re. Truss Hd. Tapping Screw ......................M5-16 .......................2  
137.......... JDP15-1137 ............Switch Cover ......................................................................................1  
138.......... TS-1533042 ............Cr. Re. Pan Head Screw ...................................M5-12 .......................2  
139.......... JDP15-1139 ............Rocker Switch ....................................................................................1  
140.......... 10614001................Motor Rod..........................................................................................1  
149.......... 2536MBE616...........Roll Pin............................................................6-25...........................2  
162.......... 10916202................Warning Label ....................................................................................1  
19  
 
Parts List JDP-15M/MF  
Index No. Part No.  
Description  
Size  
Qty  
166.......... JDP15-1166 ............Speed Diagram ..................................................................................1  
169.......... JDP15-1169 ............Trade-Mark Label ...............................................................................1  
170.......... 2658MZDU36..........Drive Screw......................................................Φ 2.3-5 ......................6  
601.......... TS-2245082 ............Cr. Re. Pan Head Screw ...................................M5-8..........................4  
602.......... TS-0733031 ............External Tooth Lock Washer..............................No 10.........................2  
610.......... TS-1534692 ............Cr. Re. Pan Head Screw ...................................M6-35 .......................2  
611.......... 10661102.... ............Seat ........................................................................................................1  
612.......... TS-1540071 ............Hex Nut............................................................M10...........................1  
613.......... 10661301................Set Bolt..............................................................................................1  
................ JDP15-1613 ............Set Bolt Assy (includes #613, 848, 849) ...............................................1  
614.......... 13005701................Nut………………………………………….M16........................................2  
615.......... 13005601................Washer ............................................................Φ24 ...........................1  
616.......... TS-1502081 ............Hex. Soc. Hd. Cap Blot .....................................M5-35 .......................1  
617.......... JDP15-1617 ............Set Ring.............................................................................................1  
618.......... 10661801................Circular Nut ........................................................................................1  
634.......... 2502ABC410...........Spring Washer..................................................Φ10 ...........................1  
700.......... TS-152704 ..............Wrench Hex .......................................................................................1  
701.......... TS-152706 ..............Wrench Hex .......................................................................................1  
702.......... TS-152707 ..............Wrench Hex .......................................................................................1  
801.......... JDP15-1801 ............Lead Wire Assy ..................................................................................1  
848.......... JDP15-1848 ............Drive Screw......................................................Φ 2.3-5 ......................2  
849.......... JDP15-1849 ............Scale .................................................................................................1  
922.......... 2801ABRF04...........Strain Relief .....................................................Φ 20 ..........................2  
999.......... TS-1540081 ............Hex Nut............................................................M12x10......................3  
20  
 
Wiring Diagram  
JDP – 15M/MF – 115V  
JDP – 15M/MF – 230V  
21  
 
NOTES  
22  
 
NOTES  
23  
 
WALTER MEIER (Manufacturing) Inc.  
427 New Sanford Road  
LaVergne, Tennessee 37086  
Phone: 800-274-6848  
 

Insignia Blu ray Player NS BRDVD3 CA User Manual
Iomega Computer Drive 3868601 User Manual
Jura Capresso Coffeemaker 68192 User Manual
JVC VCR LPT0666 001A User Manual
Karcher Vacuum Cleaner K 291 MD User Manual
Kenwood Car Stereo System DPX U5130 User Manual
KitchenAid Convection Oven KBMC140 KBMC147 KEMC308 KEMC378 KEMC307 KEMC377 YKEMC307 YKEMC308 User Manual
KitchenAid Range KDRP462L User Manual
Knoll Systems Car Amplifier MVP44a User Manual
Kodak Digital Camera CX6330 User Manual